Skip to content
Resources

Proof of delivery: building a paperwork trail that gets you paid

,8 min read

Proof of delivery (POD) is the document that shows the freight arrived: the bill of lading, or a delivery receipt, signed by the receiver with the date, the time and the condition of the load. For a carrier it is the document that turns a finished run into an invoice a broker or shipper will pay. This guide covers what makes a POD acceptable, the paperwork that has to travel with it, what the driver does at the dock, what the office does the same day, and how the whole trail decides when the money arrives.

What makes a proof of delivery acceptable

A POD gets paid when the person reading it can tell, without a phone call, that this freight reached this receiver on this date in this condition. Check for:

  • The receiver's signature and printed name. A signature alone is a scribble; the printed name is what a payables clerk matches.
  • The date and the time in and out. The date proves delivery; the times prove detention. If the receiver will not write the times, the driver writes them and notes who refused.
  • The piece count and any exception. Shortages, damage, refused pieces and reworked pallets go on the document before the receiver signs, in words a stranger can read. A "clean" POD with a problem discovered later is a claim the carrier will lose.
  • The load identifiers. The broker's load number, the shipper's BOL number, the PO number if the receiver uses one. Payables match on these, and a POD that cannot be matched sits in a queue.
  • A legible image. Flat, well lit, all four corners in the frame. A photo cut off at the signature line is not a POD.

The documents that travel together

The POD is one piece of a packet. A broker's payables desk usually wants all of it at once, and a packet missing one page waits as long as a packet missing all of them.

  • The rate confirmation, signed, with the load number the broker will look for.
  • The bill of lading, from pickup, signed by the shipper, matching the piece count the receiver later signs for.
  • The proof of delivery, as above.
  • Receipts for anything you are billing back: the lumper receipt, the scale ticket, the toll or permit receipt where the rate con lets you pass them through.
  • The invoice, with the rate con's number on it and the accessorials itemized in the words the rate con uses.

Keep the packet together from the start, per load, not per driver and not per week. The time it takes to assemble a packet from a glovebox, a text thread and an email folder is the time between delivery and invoice.

The driver's part: before the truck leaves the dock

  1. Get the signature, the printed name, the date and the times before the receiver walks away. Once the dock door closes, the receiver is somebody else's problem.
  2. Write exceptions on the document. If pallets are short or a case is crushed, it goes on the paper, and the driver photographs the damage too.
  3. Photograph the POD on the spot, flat and square, before it goes in the cab. A photo taken the next day is often a photo of a creased, coffee-stained page, if the page is still there.
  4. Send it the same hour. The office cannot invoice what is still in the cab, and the broker's paperwork deadline is counting.
  5. Add a note if anything was unusual: waited two hours, receiver refused to write times, delivered to a different door. A sentence now saves a phone call in three weeks.

The office's part: the same day, not the same week

  1. Match the POD to its load as soon as it arrives, and check it against the list above. A POD that fails the check goes back to the driver while the driver can still do something about it.
  2. Check the rate con's paperwork clause. If the POD is due in a set number of days, the invoice has a deadline too.
  3. Record the accessorials now, while the times and receipts are fresh and the driver remembers the lumper's name.
  4. Send the packet complete, in the format the broker asks for, to the address the rate con names. Many brokers have a paperwork email that is not the dispatcher's.
  5. Close the load only when the packet has gone out, and keep a list of what has been delivered but not yet invoiced. That list is where the cash is.

Worked example

What a POD sitting in the cab costs

The figures here are illustrative, not any broker's terms or any carrier's books. Take a broker who pays net 30 from receipt of complete paperwork, with a quick-pay option at a 3% fee.

  • POD sent from the dock, invoice out the same day: the thirty days start the day of delivery. Paid around day 30.
  • POD handed in at the end of the week, invoice out the following Monday: the thirty days start about a week later. Paid around day 37, for the same load.
  • POD lost, a copy requested from the receiver: two weeks of emails before the clock even starts, and a rate con with a paperwork penalty takes money off the top as well.

A carrier running several loads a week at the second pace has a week of revenue permanently stuck between delivery and invoice, and often ends up paying the quick-pay fee to pull it forward: paying 3% to recover a delay the paperwork caused. The fix is not a faster broker. It is a POD that leaves the dock the hour the freight does.

How ActionTMS keeps the paperwork trail

ActionTMS keeps the packet on the load, from the dock to the close-out, on every plan:

  • The POD from the phone, at the dock. In the driver app, a driver confirms delivery on the leg and taps Upload Photo for the proof of delivery, or Upload Document for a bill of lading, a scale ticket or a receipt, choosing the type as they go. Photos are resized on the phone before sending, so a full camera shot is fine, the upload retries on its own on bad signal, and an optional Notes field carries the "waited two hours" sentence with the picture. Drivers are free on every plan.
  • One Documents tab per load. Bill of lading, rate confirmation, proof of delivery, invoice, customs, weight ticket, photos and other, as PDFs, images, Word or Excel files up to 10 MB, with the driver's leg photos listed beside them under Driver Photos & Documents. The packet builds as the load runs and the uploads come in.
  • A close-out that checks the packet. A delivered load cannot be closed out until the bill of lading and the proof of delivery are filed in its Documents tab, where the office files the driver's dock photo, and the Completed view lists the day's finished legs so dispatch can open each load and check its PODs are filed before the drivers go home.
  • Accessorials where the paperwork is. Detention, lumper fees and other charges are recorded on the load as cost and revenue items, on the same load as the receipts that prove them.

With an AI seat, you can attach a document in the chat and the AI assistant reads it in the conversation, so "is this load ready to bill?" is a question you type, and the answer names a missing POD as a blocker.

The POD at the dock depends on the driver being on the app. If that rollout has not happened yet, start with getting drivers on a phone app without a fight.

The paperwork deadline comes from the rate con: rate confirmations, what to check before you accept a load.

Put it on this week's loads.

Request access and a workspace with sample loads is set up for you. The founder gets in touch within one business day and opens it once you have talked. Free for one office user, forever. No credit card, no contract.